Getting Started
Architecture
NServiceBus
Transports
Persistence
ServiceInsight
ServicePulse
ServiceControl
Monitoring
Samples

Amazon SQS Delayed Delivery

The SQS transport supports delayed delivery of messages for longer than 15 minutes (900 seconds) in versions 4 and above.

Enable unrestricted delayed delivery

In NServiceBus.AmazonSQS version 6 and higher the unrestricted delayed delivery feature is enabled by default. In order to work, it has to be enabled in both the sender and the receiver. When communicating with endpoints running older version of the transport ensure that it is enabled.

Unrestricted delayed delivery must be enabled on the sender and receiver to be able to delay messages longer than 900 seconds.

ScenarioSenderReceiverSupported
delay duration <= 900 secdisableddisabledYes
disabledenabledYes
enableddisabledYes
enabledenabledYes
delay duration > 900 secdisableddisabledNo
disabledenabledNo
enableddisabledNo
enabledenabledYes

Unrestricted delayed delivery requires a FIFO queue for each endpoint that receives delayed messages. The transport handles creation of the FIFO queue automatically when installers are enabled.

Manual FIFO queue creation

If installers are not used, then the FIFO queue will need to be manually created.

The FIFO queue has the following requirements:

  • The name must match the endpoint's input queue suffixed with -delay.fifo.
  • The Delivery Delay setting (DelaySeconds) should be set to 900 seconds.
  • The Message Retention Period should be set to at least 4 days.
  • A Redrive Policy must not be configured.

For an example of how to manually create queues, see scripting.

How it works

When a delayed message is sent, the delay duration is calculated. If it's less than or equal to 900 seconds, the message is sent directly to the destination input queue with the DelaySeconds message attribute set to the delay duration.

If the delay duration is greater than 900 seconds, then the message is sent to the destination's FIFO queue with the NServiceBus.AmazonSQS.DelaySeconds custom message attribute set to the delay duration. When the message is received from the FIFO queue after 900 seconds, the remaining delay duration is calculated. If it's less than or equal to 900 seconds, the message is forwarded to the destination input queue with the DelaySeconds message attribute set to the remaining delay duration. Otherwise, the message is sent back to the FIFO queue with an updated custom message attribute set to the remaining delay duration.

The following sequence diagram illustrates a message sent with a delay duration greater than 900 seconds:

sequenceDiagram participant S as Sender participant F as Destination-delay.fifo participant D as Destination S ->> F: NServiceBus.AmazonSQS.DelaySeconds = delay loop every 900sec alt remaining delay > 900sec F -->> F: NServiceBus.AmazonSQS.DelaySeconds = remaining delay else remaining delay <= 900sec F ->> D: DelaySeconds = remaining delay end end

Potential duplicate messages

While FIFO queues protect from message duplication, there are still scenarios where messages could be duplicated. To address the possibility of duplicate messages, handlers should be idempotent or the outbox feature should be enabled.

Scenario 1

As the final step, the message has to be delivered to a regular queue.

sequenceDiagram participant D as Destination participant F as Destination-delay.fifo F ->>+ F: Receive message F ->> D: Send with remaining delay Note left of D: Original message F ->>- F: Attempt to delete message Note left of F: Network outage Note right of F: Delete attempt failed Note left of F: Network restored F ->>+ F: Receive message again F ->> D: Send with remaining delay Note left of D: Duplicate message F ->>- F: Delete Message

Scenario 2

While processing a message, if a failure prevents the message from being deleted, and the next processing attempt occurs later than 5 minutes after the first attempt, then the FIFO queue will not be able to protect from message duplication.

sequenceDiagram participant F as Destination-delay.fifo activate F F ->> F: Receive message F ->> F: Send with remaining delay Note right of F: Original message with remaining delay F ->> F: Attempt to delete message deactivate F Note left of F: Network outage more than 5 mins Note right of F: Delete attempt failed Note left of F: Network restored activate F F ->> F: Receive message again F ->> F: Send with remaining delay Note right of F: Duplicate message with remaining delay F ->> F: Delete Message deactivate F

Examples

Delay of 14 minutes and 5 seconds

graph LR Sender .-> |DelaySeconds = 845sec| Destination

Delay of 32 minutes and 5 seconds

graph LR Sender fifo(Destination-delay.fifo) Destination Sender .-> |T1: NServiceBus.AmazonSQS.DelaySeconds = 1,925sec| fifo fifo --> |"T2: NServiceBus.AmazonSQS.DelaySeconds = 1,025sec"| fifo fifo .-> |"T3: DelaySeconds = 125sec"| Destination

Cost considerations

Enabling unrestricted delayed delivery will have an impact on cost because FIFO queues are required.

To estimate the cost of a delayed message, the following formula can be used:

N = delay in seconds
P = price per request
C(ycles) = N / 900
O(perations) = C * 2 // dequeue and requeue
T(otal cost) = O * P

Example

To calculate the cost of a single message delayed for a year, the following applies:

Price per 1 Million Requests after Free Tier (Monthly)

FIFO Queue: $0.50 ($0.00000050 per request)

N = 31,536,000 seconds
P = $0.00000050
C = 31,536,000 / 900 = 35,040
O = 35,040 * 2 = 70,080
T = 70,080 * $0.00000050 = $0.03504